Home › Guides › How to block knitting and crochet, and whether you need to
How to block knitting and crochet, and whether you need to
Blocking is wetting or steaming a finished piece and letting it dry flat at its final size, so the stitches even out and it keeps its shape. Wool and other animal fibres respond well to wet blocking; cotton and linen too. Acrylic changes little with water: pin it out and mist it, or skip blocking for small items, and keep heat away from it. Lace and garments gain the most.
Step by step
You need: A basin of lukewarm water, Wool wash (optional), Two clean towels, Blocking mats or a folded towel, Rust-proof pins, A tape measure.
- Soak. Put the piece in lukewarm water, with a little wool wash if you like, and press it under until it is wet through. Leave it about 15 to 20 minutes.
- Squeeze, do not wring. Lift it out supported in both hands and squeeze the water out gently. Wringing stretches the stitches.
- Roll in a towel. Lay it on a towel, roll the towel up and press on the roll, or stand on it, to take out most of the water.
- Shape and pin. Lay it flat on blocking mats or a folded towel and ease it to the measurements in the pattern. Pin the edges, closer together for lace, which you can stretch open to show the pattern.
- Leave it to dry. Leave it until it is completely dry, which can take a day or more, away from direct heat and sun. Unpin only when it is dry right through.
Which method for which yarn
| Yarn | Method | Note |
|---|---|---|
| Wool, alpaca, other animal fibres | Wet blocking, or steam | Responds well; can be stretched open for lace |
| Superwash wool | Wet blocking, gently | Can grow when wet: do not stretch it |
| Cotton | Wet blocking, or steam | Weak when wet: support its weight |
| Linen | Wet blocking | Softens with each wash |
| Acrylic | Spray blocking | Water does little; steam or heat makes it limp for good |
| Mohair and fuzzy yarns | Spray blocking | Pin it out dry, mist with water, let it dry |
| Blends | As the most delicate fibre in it | Check the yarn label |
Spray blocking
For yarns that do not like a soak, or a quick touch-up: pin the dry piece to its measurements, mist it with water from a spray bottle until it is damp, and leave it to dry.
“Did I ruin it?”
Most blocking can be redone. A wool piece blocked too big can be wet again and pinned smaller; one blocked too small can be wet and eased out. The exceptions are acrylic that has been flattened by steam or heat, which stays that way, and wool that has felted from hot water or rubbing, which does not come back.
Common questions
Do I have to block everything?
No. Garments, lace, shawls and pieces you will sew together gain the most, because blocking evens the stitches and sets the size. Amigurumi, hats in stretchy rib and quick acrylic blankets often need nothing.
Can you block acrylic?
Water changes acrylic little. Pin it out to its measurements and mist it with water (spray blocking). Steam or heat can "kill" acrylic, leaving it flat and limp for good; some makers do that on purpose for drape, so try it on the swatch first.
Should I block my gauge swatch?
Yes, the same way you will treat the finished piece. Many yarns grow or relax when wet, and a gauge measured before blocking can give a different size.
How do I block superwash wool?
Gently. Superwash wool can stretch a lot when wet, so support its weight, do not hang it, and pin it to the measurements rather than stretching it out.
Can I block in the washing machine?
Some makers use a gentle wool cycle and a spin to take out water, then lay the piece flat to dry. Only do it if the yarn label allows machine washing; feltable wool can shrink and felt.
Stuck on a step? In the YarnPath app you will be able to photograph your work, and the coach tells you what went wrong and how to fix it. About the app →
Updated 8 November 2026.